| Home | E-Submission/Review | Sitemap | Editorial Office |  
Previous issue > Previous issue

Table of Contents | April, 2022  Vol. 60   No.4 Previous Issue | Next Issue | Archive
In this issue:

Research Papers
251 A Study on the Microstructures and Mechanical Properties of Ni-Cr-Mo-V Low Alloy Steels
Ni-Cr-Mo-V계 저합금강의 미세조직과 기계적 특성에 관한 연구
Mu Geun Jo, Seong Hyeon Ryu, Kyung Il Kim, Dong Eung Kim, Jung In Kim, Kyung Taek Kim, Sang Sub Kim, Gue Serb Cho
조무근, 류성현, 김경일, 김동응, 김정인, 김경택, 김상섭, 조규섭
Korean J. Met. Mater. 2022;60(4):251-262.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.251

Ni-Cr-Mo-V steel alloys for high-speed railway brake discs were prepared to investigate the effect of alloying element contents on the microstructure and mechanical properties. The Cr, Mo, Mn alloying elements were incorporated into the steel alloys, which contained low carbon content in the range 0.16 wt.% ~ 0.21 wt.% to..... More

263 Surface Characteristics of Dental Implant Doped with Si, Mg, Ca, and P Ions via Plasma Electrolytic Oxidation
Seon-Yeong Paek, Han-Cheol Choe
박선영, 최한철
Korean J. Met. Mater. 2022;60(4):263-271.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.263

The surface characteristics of a dental implant doped with Si, Mg, Ca, and P ions via plasma electrolytic oxidation (PEO) were investigated using various experimental instruments. Plasma electrolytic oxidation of the alloy was performed in a solution containing Ca, P, Si, and Mg ions at 280 V for 3 min...... More

272 Evaluation of Liquation Cracking Susceptibility of CM247LC Superalloy Repair Welds via Pre-Weld Varestraint Test
Pre-weld Varestraint 시험을 이용한 CM247LC 초내열합금 보수용접부 액화균열 민감도 평가
Ye-Seon Jeong, Jingon Jeong, Se-Yun Kim, Sung-Hwan Bae, Uijong Lee, Hyungsoo Lee, Seong-Moon Seo, Eun-Joon Chun
정예선, 정진곤, 김세윤, 배성환, 이의종, 이형수, 서성문, 천은준
Korean J. Met. Mater. 2022;60(4):272-281.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.272

In this study, the liquation cracking susceptibility in the heat-affected zone of CM247LC superalloy gas turbine blades during repair welding was quantitatively evaluated using a newly developed pre-weld Varestraint test method. The repair welding geometry was replicated through Varestraint tests for the pre-weld bead. The liquation cracking susceptibility, that is,..... More

282 Microstructure and Mechanical Properties of Vacuum Centrifugal Casted Ti-6Al-4V Alloy by Casting and Heat Treatment
진공 원심 주조된 Ti-6Al-4V 합금의 주조 및 열처리에 따른 미세조직과 기계적 특성
Hyun-Woo Lee, Byeong-Ook Kong, Seung Eon Kim, Yunkon Joo, Sukhyun Yoon, Je Hyun Lee
이현우, 공병욱, 김승언, 주윤곤, 윤석현, 이재현
Korean J. Met. Mater. 2022;60(4):282-290.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.282

The Ti-6Al-4V alloy has been widely used for structural materials due to high specific strength property, however it is difficult to cast because of high reactivity at high temperature. In this study casting characteristics and post-casting heat treatment were studied in the cast Ti alloy. The cast alloy was prepared..... More

                           Cited By 1
291 Recovery of High-Purity Lithium Compounds from the Dust of the Smelting Reduction Process for Spent Lithium-Ion Batteries
Thanh Tuan Tran, Seong Ho Son, Man Seung Lee
손성호, 이만승
Korean J. Met. Mater. 2022;60(4):291-300.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.291

The recovery of valuable metals such as cobalt, nickel, and lithium from spent lithium-ion batteries (LIBs) has attracted much attention. In this study, a hydrometallurgical process for the recovery of high-purity lithium compounds like Li2CO3 and Li3PO4 from dust containing Li, Co, Ni, Cu, Fe, Mn, and Si produced during..... More

301 A Study on Ceramic Heater Devices Based on Si3N4 with a MoO3 Protective Layer
MoO3 보호막 적층 Si3N4 기반 세라믹 히터 소자 연구
Yong Min Jeon, Si Hong Ryu, Seon Ho Kim, Seong Eui Lee
전용민, 유시홍, 김선호, 이성의
Korean J. Met. Mater. 2022;60(4):301-306.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.301

Currently, the need for high performance heaters for industrial application is increasing, and repeated wear, rapid temperature change, and uneven temperature can cause deteriorating quality and reduced productivity. The ceramic heater in this study consists of a substrate, an electrode layer, and a protective layer, and low-melting temperature glass frit..... More

307 Enhanced Electrical Performance and Bias Stability of a-IGZO Thin-Film Transistor by Ultrasonicated Pre-annealing
초음파 전열처리를 이용한 a-IGZO 트랜지스터의 향상된 전기적 성능과 바이어스 안정성
Jae-Yun Lee, Suchang Yoo, Han-Lin Zhao, Seong-Gon Choi, Heung Gyoon Ryu, Yong Jin Jeong, Sung-Jin Kim
이재윤, 유수창, 조한림, 최성곤, 유흥균, 정용진, 김성진
Korean J. Met. Mater. 2022;60(4):307-314.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.307

Vacuum-processed oxide semiconductors have enabled incredible recent advances in the scientific research of metal oxide thin-film transistors (TFTs) and their introduction in commercial displays. Developing metal oxide transistors with low processing temperatures, on the other hand, remains a challenge. Metal oxide transistors are commonly produced at high processing temperatures (over..... More

315 Study of Phase Formation Behavior and Electronic Transport Properties in the FeSe2 -FeTe2 System
FeSe2-FeTe2 계 다결정 소재의 상 형성 거동 및 전기 전도 특성에 관한 연구
Okmin Park, TaeWan Kim, Se Woong Lee, Hyun-Sik Kim, Weon Ho Shin, Jamil Ur Rahman, Sang-il Kim
박옥민, 김태완, 이세웅, 김현식, 신원호, , 김상일
Korean J. Met. Mater. 2022;60(4):315-320.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.315

In this study, we investigated the phase formation behavior of the FeSe2-FeTe2 system and the evolution of their thermoelectric transport properties. A series of Fe(Se1-xTex)2(x = 0, 0.2, 0.6, 0.8 and 1) compounds were synthesized by conventional solid-state reaction. Single phase orthorhombic structures were formed, except for FeSe0.4Te1.6(x = 0.2)...... More

321 Hydration Deformation Behaviors of Scaffolds of Tricalcium Silicate/Tricalcium Aluminate Mixtures Printed Using the Fused Deposition Modelling (FDM)
Yeongjin Koo, Myung-Hyun Lee, Seog Young Yoon, Yoonjoo Lee
구영진, 이명현, 윤석영, 이윤주
Korean J. Met. Mater. 2022;60(4):321-328.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.321

3D printing technology has advanced rapidly over the last decade. However, for ceramic materials, drying and sintering steps are required after printing, and excessive shrinkage that occurs during these steps is a major factor that has hindered the development of the ceramic 3D printing technology. In this study, a non-sintering..... More

329 Effect of Cu on the Microstructure of Al-8Zn-2.5Mg-xCu Alloys Fabricated by Twin roll casting
박판주조법으로 제조한 Al-8Zn-2.5Mg-xCu 합금 판재의 미세조직에 미치는 Cu의 영향
Dong-Guk Kim, Yong hee Jo, Yun-Soo Lee, Yong-You Kim, Hyoung-Wook Kim, Jung-Ki Kim
김동국, 조용희, 이윤수, 김용유, 김형욱, 김정기
Korean J. Met. Mater. 2022;60(4):329-339.   Published online 2022 Mar 28
DOI: https://doi.org/10.3365/KJMM.2022.60.4.329

The effect of Cu content on the microstructure and mechanical properties of Al-8.0Zn-2.5Mg-xCu (x: 0, 1, 2, 3) aluminum alloys manufactured by the twin-roll casting process was investigated. The Al-8.0Zn-2.5Mg-xCu alloy showed an increase in surface defects with increasing Cu content. This is because the amount of residual liquid in..... More

Email Alert
Author's Index
Impact factor
The Korean Institute of Metals and Materials
SCImago Journal & Country Rank
Similarity Check
Crossref Cited-by Linking
Editorial Office
The Korean Institute of Metals and Materials
6th Fl., Seocho-daero 56-gil 38, Seocho-gu, Seoul 06633, Korea
TEL: +82-2-557-1071   FAX: +82-2-557-1080   E-mail: metal@kim.or.kr
About |  Browse Articles |  Current Issue |  For Authors and Reviewers
Copyright © The Korean Institute of Metals and Materials.                 Developed in M2PI