| Home | E-Submission/Review | Sitemap | Editorial Office |  
Most Read Articles > Browse Articles > Most Read Articles

Microstructure and Mechanical Properties of Continuous Welded 50N Rail
Wookjin Choi1, Min Ji Song1, Nam-Hyoung Lim2, and Soo Yeol Lee1,*
( 27850 times )

Rails are subjected to repeated stresses due to wheel-rail contact during train service. Rails under stress conditions undergo microstructural changes, and these cause degradations of the structural integrity and lifetime of rails. In this study, three different rails (newly-manufactured rail, newly-manufactured headhardened rail, and worn (used) rail) were compared to... More
482 Effect of Rolling Temperature on the Microstructural Characteristics of High-Speed-Rolled Mg Alloy with Initial Non-Basal Texture
비기저면 집합조직을 가지는 마그네슘 합금의 고속압연 온도 변화에 따른 압연재 미세조직 변화
( 10986 times )
Su Jin Lee, Ye Jin Kim, Jeong Hun Lee, Sung Hyuk Park
이수진, 김예진, 이정훈, 박성혁
Korean J. Met. Mater. 2019;57(8):482-490.   Published online 2019 Jul 4
DOI: https://doi.org/10.3365/KJMM.2019.57.8.482

In this study, the effects of rolling temperature on the microstructural characteristics of a highspeed-rolled Mg alloy with a non-basal texture were investigated. To this end, commercial AZ31 alloy samples in which the basal poles of most grains were tilted at an angle of 45° from the normal direction (ND)..... More

462 Effect of Process Parameters on the Angular Distribution of Sputtered Cu Flux in Long-Throw Sputtering System
( 7797 times )
Hee-Young Shin, Tae-Ho Kim, Jun-Woo Park, Hyun-Chul Sohn
Korean J. Met. Mater. 2019;57(7):462-467.   Published online 2019 Jun 5
DOI: https://doi.org/10.3365/KJMM.2019.57.7.462

In this work, the angular distribution of the sputtered Cu flux in a long throw sputtering (LTS) system is extracted from the comparison of experimentally-measured profiles of deposited films with simulated profiles of films in overhang contact structure. And effects of the sputtering process parameters such as Ar pressure during..... More

778 Effect of Hot Stamping Heat Treatment Temperature on Resistance Spot Weldability of Al-10% Si Coated 30MnB5 Steel
핫스탬핑 열처리 온도가 Al-10% Si 도금 30MnB5 강의 점용접성에 미치는 영향
( 7627 times )
Seong Guk Son, Yeonjung Hwang, Chang Wook Lee, Ji Hong Yoo, Minsu Choi
손성국, 황연정, 이창욱, 유지홍, 최민수
Korean J. Met. Mater. 2019;57(12):778-786.   Published online 2019 Oct 8
DOI: https://doi.org/10.3365/KJMM.2019.57.12.778

Hot stamping is the most efficient manufacturing process to produce high strength automotive parts with reduced springback. Recently, 30MnB5 steel has been developed for hot stamping steel which can provide above 1700 MPa. However, resistance spot weldability of this steel is insufficient due to the need for a large amount..... More

310 Effect of BN Addition on the Mechanical Properties of AlN
AlN 기계적 성질에 미치는 BN 첨가 영향
( 5509 times )
Woo-Jin Cho, Se-Hoon Oh, In-Jin Shon
조우진, 오세훈, 손인진
Korean J. Met. Mater. 2019;57(5):310-315.   Published online 2019 Apr 10
DOI: https://doi.org/10.3365/KJMM.2019.57.5.310

Aluminum nitride (AlN) has several attractive properties including high thermal conductivity, excellent electrical insulation, a thermal expansion coefficient close to that of Si and low density. Accordingly, it is considered a promising packing material and substrate for high power integrated circuits. However, its low fracture toughness at room temperature limits..... More

                           Cited By 2
71 Effect of Stress Magnitude on the Tensile Properties of Damaged Damping Alloy Under Fatigue Stress
피로손상된 제진합금의 인장성질에 미치는 피로응력 크기의 영향
( 5501 times )
Myong-Soo Lee, Kwon-Hoo Kim, Chang-Yong Kang
이명수, 김권후, 강창룡
Korean J. Met. Mater. 2019;57(2):71-76.   Published online 2019 Jan 8
DOI: https://doi.org/10.3365/KJMM.2019.57.2.71

This study was carried out to investigate the effect of fatigue stress magnitude on the tensile properties of the damaged Fe – 22Mn – 12Cr – 3Ni – 2Si – 4Co damping alloy under various fatigue stress magnitudes. α´ and ε-martensite were formed by fatigue stress in the Fe –..... More

430 A Study on Micro-Structure and Wear Behavior of AISI M4 and CPM15V Deposited by Laser Melting
레이저 용융 적층 기술을 이용한 AISI M4와 CPM15V 분말 적층부의 미세 조직 및 마모 특성에 관한 연구
( 5306 times )
Gyeong Yun Baek, Gwang Yong Shin, Ki Yong Lee, Do Sik Shim
백경윤, 신광용, 이기용, 심도식
Korean J. Met. Mater. 2018;56(6):430-439.   Published online 2018 Jun 4
DOI: https://doi.org/10.3365/KJMM.2018.56.6.430

AISI M4 and CPM15V are used as tool steels since they have high hardness and wear resistance. This study is concerned with die and mold hardfacing using laser melting deposition with M4 and CPM15V powders. For this purpose, the two types of metal powders were deposited on SKD11 base metal,..... More

                           Cited By 2
413 Correlation of Microstructural Factors with the Yield Ratio and Uniform Elongation in API X80 Linepipe Steels
API X80 라인파이프강의 미세조직적 인자와 항복비 및 균일 연신율의 상관관계
( 5283 times )
Sang-In Lee, Seung-Wan Lee, Seok Gyu Lee, Sunghak Lee, Hwan Gyo Jung, Byoungchul Hwang
이상인, 이승완, 이석규, 이성학, 정환교, 황병철
Korean J. Met. Mater. 2018;56(6):413-422.   Published online 2018 Jun 4
DOI: https://doi.org/10.3365/KJMM.2018.56.6.413

In the present study, the correlation of microstructural factors with yield ratio and uniform elongation was investigated in API X80 linepipe steels with different microstructures by varying thermomechanical control process conditions. The grain size and microstructure fraction of the API X80 linepipe steels were quantitatively measured by EBSD analysis and then..... More

                           Cited By 3
352 Visualization of Magnetic Domains in Electrical Steel Using High-Resolution Dark-Field Imaging
( 4980 times )
Youngju Kim, Jongyul Kim, Daniel Seth Hussey, Oh Youl Kwon, Seung Wook Lee
Korean J. Met. Mater. 2019;57(6):352-359.   Published online 2019 May 16
DOI: https://doi.org/10.3365/KJMM.2019.57.6.352

Electrical steel is a soft magnetic steel material used in electric devices such as transformers and motors. The performance of these electric devices is primarily related to the magnetic properties of electrical steel, and the assessment of the magnetic properties of electrical steel has been considered an important topic. We..... More

                           Cited By 1
635 Investigation of Local Deformation Behaviour of Metallic Materials and Recent Research Trends: A Review
금속 재료의 국부 변형 거동 분석 방법과 연구 동향: 리뷰
( 4632 times )
Min-su Lee, Jong Bae Jeon, Tea-Sung Jun
이민수, 전종배, 전태성
Korean J. Met. Mater. 2018;56(9):635-644.   Published online 2018 Sep 5
DOI: https://doi.org/10.3365/KJMM.2018.56.9.635

The behaviour and performance of complex metallic materials (e.g., advanced high strength steel and dual phase Ti alloys) are acknowledged to be multi-scale in nature and to rely on the details of the threedimensional morphology, chemistry and crystallography at the meso-scale level and on macro-scale level geometry and boundary and..... More

Email Alert
Author's Index
Impact factor
The Korean Institute of Metals and Materials
SCImago Journal & Country Rank
Similarity Check
Crossref Cited-by Linking
Editorial Office
The Korean Institute of Metals and Materials
6th Fl., Seocho-daero 56-gil 38, Seocho-gu, Seoul 06633, Korea
TEL: +82-2-557-1071   FAX: +82-2-557-1080   E-mail: metal@kim.or.kr
About |  Browse Articles |  Current Issue |  For Authors and Reviewers
Copyright © The Korean Institute of Metals and Materials. All rights reserved.                 Developed in M2Community